Roborock Qrevo Curv 2 Flow Roller Mop Robot Vacuum With Multifunctional Dock

The Roborock Qrevo Curv 2 Flow is a robot vacuum and roller-mop combo built around one idea: the mop should never spread yesterday's dirt. Its SpiraFlow system feeds fresh water to a 270 mm extra-wide roller mop and scrapes the dirty water away in real time, so the roller stays clean through the entire run instead of waiting for a wash cycle back at the dock. Up front, 20,000 Pa of HyperForce suction and a certified Dual Zero-Tangle System handle debris and hair on carpet and hard floors.

The multifunctional dock takes over the maintenance work: it empties the robot's dust bin for up to 65 days at a time, washes the roller with 167 F hot water, re-washes it when dirt sensors say it is still dirty, and dries it with 131 F warm air. Reactive AI obstacle recognition identifies more than 200 object types, and pet recognition is built into the app's SmartPlan 3.0 cleaning logic.

Within the Roborock lineup, the Qrevo Curv 2 Flow is the roller-mop specialist of the Qrevo family - the model to pick when real mopping performance on sealed hard floors matters as much as vacuuming, especially in homes with pets and frequent tracked-in messes.

• SpiraFlow Self-Cleaning Roller Mop: The 270 mm roller is rinsed with fresh water through 8 hydration points and scraped clean of dirty water continuously while it mops, so it cleans with fresh water from the first room to the last instead of pushing around what it already picked up.
• 20,000 Pa HyperForce Suction: Pulls embedded debris out of carpet fibers and grout lines, with pressure-boosted mopping at up to 15 N and 220 RPM for dried-on messes.
• Dual Zero-Tangle System: The DuoDivide main brush and dual lifting arc side brushes are certified for a 0 percent hair tangling rate - long hair and pet hair go into the bin, not around the brush.
• Carpet Protection: The roller lifts up to 15 mm and tucks behind the Roller Shield when the robot crosses carpet, keeping wet mop contact off the pile.
• Reactive AI Obstacle Recognition: An RGB camera identifies more than 200 object types - cables, shoes, toys, pet waste - and steers around them, with pet recognition built into SmartPlan 3.0.
• Hands-Free Multifunctional Dock: Auto-empties the dust bin for up to 65 days, washes the roller in 167 F hot water, re-washes when dirt is still detected, dries with 131 F warm air, and keeps clean and dirty water separated in a self-cleaning tray.
• PreciSense LiDAR Mapping: Builds a 3D map with 6x faster quick mapping and stores maps for up to 4 floors.
• Voice and Smart Home Control: The built-in Hello Rocky voice assistant answers directly on the robot, and Matter support (via OTA update) ties it into smart home platforms.

The Qrevo Curv 2 Flow suits homes where mopping is a daily need rather than an occasional extra: kitchens that see spills and tracked-in dirt, entryways, tile and sealed hardwood throughout, and households with dogs or cats. The always-clean roller matters most for pet owners - paw prints, drool, and litter dust get lifted with fresh water instead of smeared - while the zero-tangle brushes and 65-day auto-empty keep shedding season manageable. Mixed flooring works too, since the roller lifts 15 mm over carpet while the 20,000 Pa suction takes over.

Within the Qrevo family, choose the Curv 2 Flow for the strongest mopping; if you prefer an ultra-slim robot with dual spinning mops and 4 cm threshold climbing, look at the Roborock Qrevo CurvX, and for maximum suction with edge-focused cleaning, see the Roborock Qrevo Edge 2.

1. Unbox and remove protectors: Take off all protective films and foam strips from the robot, roller mop, and dock, and confirm the disposable dust bag is seated in the dock.
2. Place the dock: Set the multifunctional dock on a hard, level surface against a wall near an outlet, leaving open clearance on both sides and in front per the quick start guide.
3. Fill and charge: Fill the clean water tank, dock the robot, and let it charge - a full charge from 15 percent takes about 3 hours.
4. Pair in the Roborock app: Download the Roborock app, create or sign in to your account, and follow the prompts to connect the robot to your home Wi-Fi.
5. Run the first mapping cycle: Start Quick Mapping so the robot builds its 3D map, then check the room divisions, name rooms, and add floors if needed (up to 4 maps).
6. Set schedules and zones: Create cleaning schedules, no-go zones, and no-mop zones, and let SmartPlan 3.0 pick routines - or fine-tune suction, water flow, and re-wash behavior per room.